JJ Deng
Forum Replies Created
-
AuthorPosts
-
JJ Deng
ParticipantHi Peter,
thanks for reply. Is there product plan for supporting P2P Lora Conduit?
BTW, is it possibel to plug-in 2 Lora cards via PCIe in the same Gateway, which can work in parralel?JJ Deng
ParticipantHi Jeff, thanks for reply
JJ Deng
ParticipantHi *,
after removal of the Battery and restart the device, i can get the following information via the TeraTerm. And it stacks there without further progressing
**********************************
.data : 0xc0518000 – 0xc05407a0 ( 162 kB)
.bss : 0xc05407a0 – 0xc055f408 ( 124 kB)
NR_IRQS:16 nr_irqs:16 16
sched_clock: 32 bits at 100 Hz, resolution 10000000ns, wraps every 4294967286ms
Calibrating delay loop… 199.06 BogoMIPS (lpj=995328)
pid_max: default: 32768 minimum: 301
Mount-cache hash table entries: 512
Initializing cgroup subsys blkio
CPU: Testing write buffer coherency: ok
Setting up static identity map for 0xc03a9b70 – 0xc03a9bc8
devtmpfs: initialized
pinctrl core: initialized pinctrl subsystem
NET: Registered protocol family 16
DMA: preallocated 256 KiB pool for atomic coherent allocations
AT91: Power Management (with slow clock mode)
AT91: Starting after general reset
gpio-at91 fffff400.gpio: at address fefff400
gpio-at91 fffff600.gpio: at address fefff600
gpio-at91 fffff800.gpio: at address fefff800
gpio-at91 fffffa00.gpio: at address fefffa00
pinctrl-at91 pinctrl.2: initialized AT91 pinctrl driver
bio: create slab <bio-0> at 0
at_hdmac ffffec00.dma-controller: Atmel AHB DMA Controller ( cpy slave ), 8 channels
at_hdmac ffffee00.dma-controller: Atmel AHB DMA Controller ( cpy slave ), 8 channels
SCSI subsystem initialized
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
i2c-gpio i2c.3: using pins 30 (SDA) and 31 (SCL)
i2c-gpio i2c.4: using pins 64 (SDA) and 65 (SCL)
Switched to clocksource tcb_clksrc
NET: Registered protocol family 2
TCP established hash table entries: 2048 (order: 2, 16384 bytes)
TCP bind hash table entries: 2048 (order: 1, 8192 bytes)
TCP: Hash tables configured (established 2048 bind 2048)
TCP: reno registered
UDP hash table entries: 256 (order: 0, 4096 bytes)
UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
NET: Registered protocol family 1
RPC: Registered named UNIX socket transport module.
RPC: Registered udp transport module.
RPC: Registered tcp transport module.
RPC: Registered tcp NFSv4.1 backchannel transport module.
NFS: Registering the id_resolver key type
Key type id_resolver registered
Key type id_legacy registered
jffs2: version 2.2. (NAND) (SUMMARY) ?2001-2006 Red Hat, Inc.
ROMFS MTD (C) 2007 Red Hat, Inc.
msgmni has been set to 496
Block layer SCSI generic (bsg) driver version 0.4 loaded (major 252)
io scheduler noop registered (default)
io scheduler deadline registered
io scheduler cfq registered
fffff200.serial: ttyS0 at MMIO 0xfffff200 (irq = 16, base_baud = 8333333) is a ATMEL_SERIAL
console [ttyS0] enabled
f8040000.serial: ttyS1 at MMIO 0xf8040000 (irq = 26, base_baud = 8333333) is a ATMEL_SERIAL
brd: module loaded
loop: module loaded
at24_get_setup: found a match for eeprom at 56
at24 0-0056: 512 byte 24c04 EEPROM, writable, 16 bytes/write
sam9x5: read 512 bytes from id eeprom
at24_get_setup: found a match for eeprom at 50
at24 1-0050: 512 byte 24c04 EEPROM, writable, 16 bytes/writeJJ Deng
ParticipantWhatever i try, there is no response of input via micro usb debug port on the front plate.
JJ Deng
ParticipantDear all,
i got the same issue here.
Can anyone share the information, how to reset it?
30S button reset didn’t work at all. -
AuthorPosts