Richard Wenner

Forum Replies Created

Viewing 5 posts - 1 through 5 (of 5 total)
  • Author
    Posts
  • November 27, 2017 at 8:06 am in reply to: How to dectypt the messages sent by mDot box in Lora demo mode #21902
    Richard Wenner
    Participant

    I did a brief video on the topic https://youtu.be/WizST6gighs

    October 24, 2017 at 3:41 am in reply to: How to dectypt the messages sent by mDot box in Lora demo mode #21261
    Richard Wenner
    Participant

    Steve, You are making me feel bad at my late-night outburst now! These sites are all great and extremely well documented (first class) but obviously written by folk who know the products AND these site(s) very well. Cross-referencing say the video with that mass of Node Red code would have helped. The videos are minutely detailed and then miss out these vital links. They just appear from nowhere.

    October 22, 2017 at 8:34 pm in reply to: How to dectypt the messages sent by mDot box in Lora demo mode #21251
    Richard Wenner
    Participant

    Why is everything here like drawing teeth? If Vinesh had not raised his question – where would the data have been seen?

    March 8, 2017 at 5:02 pm in reply to: Point to Point #17730
    Richard Wenner
    Participant

    Two questions
    1) Why do only single characters appear? It’s as if there need to be a send function.
    2) What is the escape sequence to leave the mode?

    Device ID: 00:80:00:00:04:00:03:58
    Frequency Band: EU868
    Frequency Sub Band: 0
    Public Network: on
    Start Up Mode: COMMAND
    Network Address: 00112233
    Network ID: 70:b3:d5:7e:f0:00:3a:a1
    Network ID Passphrase:
    Network Key: 59.cb.4b.2d.aa.33.87.6f.f8.7f.f8.9d.ee.5b.e9.fc
    Network Key Passphrase:
    Network Session Key: 00.11.22.33.00.11.22.33.00.11.22.33.00.11.22.33
    Data Session Key: 33.22.11.00.33.22.11.00.33.22.11.00.33.22.11.00
    Network Join Mode: PEER_TO_PEER
    Network Join Retries: 2
    Preserve Session: off
    Join Byte Order: MSB
    Join Delay: 5
    Join Rx1 DR Offset: 0
    Join Rx2 Datarate: DR0 – SF12BW125
    Join Rx2 Frequency: 869525000
    App Port: 1
    Link Check Threshold: off
    Link Check Count: off
    Error Correction: 1 bytes
    ACK Retries: off
    Packet Repeat: 1
    Encryption: on
    CRC: on
    Adaptive Data Rate: off
    Command Echo: on
    Verbose Response: off
    Tx Frequency: 0
    Tx Data Rate: DR1 – SF11BW125
    Tx Power: 7
    Tx Antenna Gain: 3
    Tx Wait: on
    Tx Inverted Signal: off
    Rx Delay: 1 s
    Rx Inverted Signal: on
    Rx Output Style: HEXADECIMAL
    Debug Baud Rate: 115200
    Serial Baud Rate: 115200
    Serial Flow Control: off
    Serial Clear On Error: on
    Wake Mode: INTERVAL
    Wake Interval: 10 s
    Wake Delay: 100 ms
    Wake Timeout: 20 ms
    Wake Pin: WAKE
    Log Level: 0

    February 8, 2017 at 4:40 pm in reply to: Upgrade 1.2.2 issue #16833
    Richard Wenner
    Participant

    I too had the upgrade failure (using both Chrome & Moz). Powering down did not work but the manual method works fine. 1.3.3 ok

  • Author
    Posts
Viewing 5 posts - 1 through 5 (of 5 total)