Jose Olvera
Forum Replies Created
-
AuthorPosts
-
Jose Olvera
Participantyour are correct…after PUBLIC was uncheck … I had success to join network
Jose Olvera
Participantissue : asking mdot documentation ( AT commands ) for RX/TX RF Testing
status: I just got the Conduit and Dev Kit (Mdot) and finally able to had success to join to the network
next step : I need to send an AT command to keep the TX ON and transmit a burst with any payload continuously until another AT command is send to STOP and turn OFF the TX
details : we use words like : signaling and non-signaling when we are doing RF testing. when we are testing the upper layers of a protocol we will use the name ‘signaling mode’ and when we only test the PHYSICAL layer 1 (RF RADIO) we use name ‘non-signaling’ and is used to test RF Power and RF Modulation, etc.
To do non-signaling , the device (mdot) in this case , needs to be sent in TEST-MODE , and that is why I am asking DOCUMENTATION of all AT commands available to :
– change frequency or change band
– change TX power level
– change the payload
– change the number of packets or burst to transmit
– etcRegards
JoseJose Olvera
Participantstep 2 : RMA request
Hello Brandon (Multitech) , please advise how to ask for an RMA to return this units to Multitech and get another working setNOTE: I would like to send you both : the Gateway (Conduit) and the DEV KIT LoRa
Attn name ?
full address ?
RMA number ?NOTE: see additional commands and responses below
ERROR
AT+RSSI
0, 0, 0, 0OK
AT+PING
Network Not JoinedJose Olvera
Participantstep 2 : RMA request
Hello Brandon (Multitech) , please advise how to ask for an RMA to return this units to Multitech and get …a replacementAttn name ?
full address ?
RMA number ?NOTE: see additional commands and responses below
ERROR
AT+RSSI
0, 0, 0, 0OK
AT+PING
Network Not JoinedJose Olvera
ParticipantNote: I am an RF engineer (I am not an ‘network’ engineer) and some of these tools used by your systems are new to me :
– I failed to do a simple copy/paste screen shot (png file), the system does not allows me to ‘paste’
– How to copy/paste here the….. /var/config/db.json
Jose Olvera
ParticipantTHE CONDUIT FIRMWARE WAS UPGRADED TO …LATEST … 1.0.33
Jose Olvera
Participantpart 3 : display ( query ) the status
=~=~=~=~=~=~=~=~=~=~=~= PuTTY log 2015.11.13 11:03:12 =~=~=~=~=~=~=~=~=~=~=~=
ATIMultiTech mDot
Firmware: 0.1.4
Library : 0.0.9OK
AT&VDevice ID: 00:80:00:00:00:00:a2:77
Frequency Band: FB_915
Frequency Sub Band: 1
Public Network: off
Start Up Mode: COMMAND
Network Address: 00000000
Network ID: 70:77:46:a9:0d:86:9c:dd
Network ID Passphrase: testnetwork
Network Key: 9f.20.a1.ef.95.8d.86.28.cd.83.cb.66.ee.9e.61.7a
Network Key Passphrase: testnetwork
Network Session Key: 00.00.00.00.00.00.00.00.00.00.00.00.00.00.00.00
Data Session Key: 00.00.00.00.00.00.00.00.00.00.00.00.00.00.00.00
Network Join Mode: OTA
Network Join Retries: 2
Join Byte Order: LSB
Link Check Threshold: off
Link Check Count: off
Error Correction: 1 bytes
ACK Retries: off
Encryption: on
CRC: on
Adaptive Data Rate: off
Command Echo: on
Verbose Response: off
Tx Frequency: 0
Tx Data Rate: SF_9
Tx Power: 11
Tx Wait: on
Tx Inverted Signal: off
Rx Frequency: 903700000
Rx Data Rate: SF_9
Rx Inverted Signal: on
Rx Output Style: HEXADECIMAL
Debug Baud Rate: 115200
Serial Baud Rate: 115200
Wake Mode: INTERVAL
Wake Interval: 10 s
Wake Delay: 100 ms
Wake Timeout: 20 ms
Log Level: 0OK
AT+NI70:77:46:a9:0d:86:9c:dd
Passphrase: ‘testnetwork’OK
AT+JOINJoin Error – Failed to join network
ERROR
Jose Olvera
ParticipantPART 2 : QUERY the setup … looks OK
NOTE: the ‘RESET’ … does not seem to do anything ? no LED blinking
NOTE : the firmware upgrade was saved …but…. after power cycle …the LED turns RED, and I need to reload the firmware and wait for LED to turn GREEN=~=~=~=~=~=~=~=~=~=~=~= PuTTY log 2015.11.13 10:50:37 =~=~=~=~=~=~=~=~=~=~=~=
AT+FSB1
OK
at+freq AR T+FREQFB_915
OK
AT+NI70:77:46:a9:0d:86:9c:dd
Passphrase: ‘testnetwork’OK
AT+NK9f.20.a1.ef.95.8d.86.28.cd.83.cb.66.ee.9e.61.7a
Passphrase: ‘testnetwork’OK
AT+JOINJoin Error – Failed to join network
ERROR
Jose Olvera
Participantfollow up
– the LoRa DEV KIT has the LED Green( after firmware upgrade)
– Not using the 5V Power Supply
– the screen shot and AT are below=~=~=~=~=~=~=~=~=~=~=~= PuTTY log 2015.11.13 10:27:29 =~=~=~=~=~=~=~=~=~=~=~=
AT&FOK
AT&WOK
ATIMultiTech mDot
Firmware: 0.1.4
Library : 0.0.9OK
AT&WOK
AT+FSB=1OK
AT+NI=1,testnetworkSet Network Name: testnetwork
OK
AT+NK=1,testnetworkSet Network Passphrase: testnetwork
OK
AT&WOK
AT+JOINJoin Error – Failed to join network
ERROR
Jose Olvera
Participant-The Conduit and the LoRa have the same settings
which is BAND1, 915Mhz, netname= testnetwork
-The DEV KIT came without the 5V Power Supply, and the only power comes from the USB cableJose Olvera
ParticipantI just got a new box ( Multitech Conduit), the LoRa is set for band 1 (915 Mhz)
the TXpower = 20 dBmquestion/problem : I cannot ‘see’ the RF signal
setup : I have an Spectrum Analyzer and using an antenna expecting to pick
the signal from the LoRa. The antenna can pick some other signal in the air
near 915 Mhz, but …. it seem ths box is not transmitting -
AuthorPosts