Point to Point

Home › Forums › mDot/xDot › Point to Point

Tagged: 

Viewing 3 posts - 1 through 3 (of 3 total)
  • Author
    Posts
  • February 17, 2017 at 8:39 am #17291
    Richard Wenner
    Participant

    I have a pair of MTMDK-xdot-eu1-aoo both with these settings
    at&v
    Device ID: 00:80:00:00:04:00:03:22
    Frequency Band: EU868
    Frequency Sub Band: 0
    Public Network: on
    Start Up Mode: COMMAND
    Network Address: 11111111
    Network ID: 2b:7e:15:16:28:ae:d2:a5
    Network ID Passphrase:
    Network Key: 2b.7e.15.16.28.ae.d2.a6.ab.f7.15.88.09.cf.4f.45
    Network Key Passphrase:
    Network Session Key: 2b.7e.15.16.28.ae.d2.a6.ab.f7.15.88.09.cf.4f.3c
    Data Session Key: 2b.7e.15.16.28.ae.d2.a6.ab.f7.15.88.09.cf.4f.3c
    Network Join Mode: PEER_TO_PEER
    Network Join Retries: 2
    Preserve Session: off
    Join Byte Order: LSB
    Join Delay: 5
    Join Rx1 DR Offset: 0
    Join Rx2 Datarate: DR0 – SF12BW125
    Join Rx2 Frequency: 869525000
    App Port: 1
    Link Check Threshold: off
    Link Check Count: off
    Error Correction: 1 bytes
    ACK Retries: off
    Packet Repeat: 1
    Encryption: on
    CRC: on
    Adaptive Data Rate: off
    Command Echo: on
    Verbose Response: off
    Tx Frequency: 0
    Tx Data Rate: DR0 – SF12BW125
    Tx Power: 20
    Tx Antenna Gain: 3
    Tx Wait: on
    Tx Inverted Signal: off
    Rx Delay: 1 s
    Rx Inverted Signal: off
    Rx Output Style: HEXADECIMAL
    Debug Baud Rate: 115200
    Serial Baud Rate: 115200
    Serial Flow Control: off
    Serial Clear On Error: on
    Wake Mode: INTERVAL
    Wake Interval: 10 s
    Wake Delay: 100 ms
    Wake Timeout: 20 ms
    Wake Pin: WAKE
    Log Level: 0

    How do you get into/out of sharing details typed at the terminal (which I assume is the way it works) st+sd / at+send= both cause nothing to appear anywhere on any screen (please)

    February 20, 2017 at 12:55 am #17351
    FARRUKH
    Participant

    after you type AT+SD,
    whatever you type, it is received on connected radio modules.
    I’ve tested and it works.

    March 8, 2017 at 5:02 pm #17730
    Richard Wenner
    Participant

    Two questions
    1) Why do only single characters appear? It’s as if there need to be a send function.
    2) What is the escape sequence to leave the mode?

    Device ID: 00:80:00:00:04:00:03:58
    Frequency Band: EU868
    Frequency Sub Band: 0
    Public Network: on
    Start Up Mode: COMMAND
    Network Address: 00112233
    Network ID: 70:b3:d5:7e:f0:00:3a:a1
    Network ID Passphrase:
    Network Key: 59.cb.4b.2d.aa.33.87.6f.f8.7f.f8.9d.ee.5b.e9.fc
    Network Key Passphrase:
    Network Session Key: 00.11.22.33.00.11.22.33.00.11.22.33.00.11.22.33
    Data Session Key: 33.22.11.00.33.22.11.00.33.22.11.00.33.22.11.00
    Network Join Mode: PEER_TO_PEER
    Network Join Retries: 2
    Preserve Session: off
    Join Byte Order: MSB
    Join Delay: 5
    Join Rx1 DR Offset: 0
    Join Rx2 Datarate: DR0 – SF12BW125
    Join Rx2 Frequency: 869525000
    App Port: 1
    Link Check Threshold: off
    Link Check Count: off
    Error Correction: 1 bytes
    ACK Retries: off
    Packet Repeat: 1
    Encryption: on
    CRC: on
    Adaptive Data Rate: off
    Command Echo: on
    Verbose Response: off
    Tx Frequency: 0
    Tx Data Rate: DR1 – SF11BW125
    Tx Power: 7
    Tx Antenna Gain: 3
    Tx Wait: on
    Tx Inverted Signal: off
    Rx Delay: 1 s
    Rx Inverted Signal: on
    Rx Output Style: HEXADECIMAL
    Debug Baud Rate: 115200
    Serial Baud Rate: 115200
    Serial Flow Control: off
    Serial Clear On Error: on
    Wake Mode: INTERVAL
    Wake Interval: 10 s
    Wake Delay: 100 ms
    Wake Timeout: 20 ms
    Wake Pin: WAKE
    Log Level: 0

  • Author
    Posts
Viewing 3 posts - 1 through 3 (of 3 total)
  • You must be logged in to reply to this topic.